SOP for Monitoring Air Emissions During Waste Incineration

Posted on By

SOP for Monitoring Air Emissions During Waste Incineration

Standard Operating Procedure for Monitoring Air Emissions During Waste Incineration

1) Purpose

The purpose of this SOP is to establish a systematic procedure for monitoring air emissions generated during waste incineration to ensure compliance with environmental standards and minimize the release of harmful pollutants into the atmosphere.

2) Scope

This SOP applies to all waste incineration processes within the facility, including the incineration of hazardous, biomedical, and general waste. It is relevant to personnel responsible for waste management, environmental monitoring, and equipment maintenance.

3) Responsibilities

  • Environmental Officers: Oversee the air emission monitoring process and ensure compliance with regulations.
  • Incinerator Operators: Operate incinerators as per standard procedures and assist in emission monitoring activities.
  • Maintenance Personnel: Maintain emission monitoring equipment and ensure proper calibration.
  • Compliance Team: Document and report emission data to regulatory authorities as required.

4) Procedure

4.1 Regulatory Requirements and Standards

  1. Emission Limits:
    • Comply with emission standards for pollutants such as particulate matter (PM), sulfur dioxide (SO₂), nitrogen oxides (NOₓ), carbon monoxide (CO), and dioxins/furans as prescribed by local environmental authorities.

    2. less
    Copy code

  2. Guidelines:
    • Follow guidelines issued by regulatory bodies such as the EPA, CPCB, or equivalent agencies.
See also  SOP for Managing Radioactive Materials

4.2 Preparation for Emission Monitoring

  1. Inspection of Monitoring Equipment:
    • Ensure that stack monitoring systems, probes, and sampling devices are functional and calibrated.
    • Conduct pre-operation checks to verify equipment integrity and connectivity.

    2. less
    Copy code

  2. Selection of Monitoring Locations:
    • Install stack monitoring equipment at appropriate locations to capture representative emission samples.
    • Ensure that sampling ports and access points comply with regulatory specifications.

4.3 Real-Time Monitoring of Emissions

  1. Continuous Emission Monitoring System (CEMS):
    • Operate the CEMS to measure parameters such as PM, CO, SO₂, and NOₓ in real time.
    • Log data automatically into the system’s data acquisition software.

    2. less
    Copy code

  2. Manual Sampling (if applicable):
    • Use portable gas analyzers or isokinetic sampling devices to measure pollutant levels.
    • Follow standard methods (e.g., EPA Method 5 for PM, Method 23 for dioxins/furans).
See also  SOP for Inspection of Hazardous Material Storage Areas

4.4 Data Recording and Analysis

  1. Recording Emission Data:
    • Log real-time data from CEMS and manual sampling results into the Emission Monitoring Log (Annexure 1).
    • Record key parameters such as temperature, gas flow rate, and pollutant concentrations.

    2. less
    Copy code

  2. Data Analysis:
    • Compare emission levels with regulatory limits to identify non-compliance or anomalies.
    • Perform trend analysis to detect changes in emission patterns over time.

4.5 Corrective Actions

  1. Operational Adjustments:
    • Optimize incinerator temperature and air supply to minimize pollutant formation.
    • Address abnormal operating conditions (e.g., incomplete combustion or excess oxygen).

    2. less
    Copy code

  2. Maintenance of Equipment:
    • Inspect and clean incinerator components such as burners, filters, and scrubbers regularly.
    • Calibrate and maintain CEMS equipment as per manufacturer recommendations.
  3. Incident Reporting:
    • Document any exceedances or equipment malfunctions in the Emission Incident Report Log (Annexure 2).
    • Report non-compliance incidents to the regulatory authorities within the stipulated time frame.
See also  SOP for Creating and Reviewing Risk Assessment Reports

4.6 Documentation and Reporting

  1. Maintain Records:
    • Store emission monitoring logs, calibration certificates, and incident reports for a minimum of 5 years.

    2. less
    Copy code

  2. Regulatory Reporting:
    • Submit periodic emission reports to the relevant authorities, as per compliance requirements.

5) Abbreviations, if any

  • CEMS: Continuous Emission Monitoring System
  • PM: Particulate Matter
  • CO: Carbon Monoxide
  • SO₂: Sulfur Dioxide
  • NOₓ: Nitrogen Oxides

6) Documents, if any

  • Emission Monitoring Log
  • Emission Incident Report Log
  • Calibration Records
  • Regulatory Reports

7) Reference, if any

  • EPA Emission Standards
  • CPCB Guidelines for Waste Incineration
  • ISO 14001 Environmental Management Systems

8) SOP Version

Version: 1.0

Annexure

Template 1: Emission Monitoring Log

 
 
 Date Time Parameter Measured Value Regulatory Limit Operator Name 
 
 DD/MM/YYYY HH:MM PM 10 µg/m³ 20 µg/m³ John Doe

Template 2: Emission Incident Report Log

 
 
 Date Time Incident Description Corrective Action Taken Reported By 
 
 DD/MM/YYYY HH:MM SO₂ levels exceeded limit Adjusted temperature and air supply Jane Smith
Environment, Health and Safety Tags:, , , , , , , , , , , , , , , , , , , , , , , , , , , , ,